Thread Number: 2010
2 washers and 2 dryers.
[Down to Last]

automaticwasher.org's exclusive eBay Watch:
scroll >>> for more items --- [As an eBay Partner, eBay may compensate automaticwasher.org if you make a purchase using any link to eBay on this page]
Post# 65521   5/5/2005 at 20:05 (6,928 days old) by Acerone ()        

My dream laundry will have 2 stacked washers and dryers. The plumber just finished the hookup today. I can't wait until the house is finished.

Anyone else have their laundry room setup with 2 washers and dryers?





Post# 65522 , Reply# 1   5/5/2005 at 20:08 (6,928 days old) by westytoploader ()        

Do you plan to have Westy SpaceMates?? That should be on your top priority list!! :)

Post# 65525 , Reply# 2   5/5/2005 at 20:15 (6,928 days old) by PeteK (Ontari ari ari O )        

petek's profile picture
I think I wouldn't mind a set on the main floor near the bedrooms or if having a large ensuite bathroom, right in there. Then another downstairs would be nice for guest use etc. When my 649 ticket comes in of course.

Post# 65527 , Reply# 3   5/5/2005 at 20:53 (6,928 days old) by david (CA)        
here is my laundry room off the master bedroom

We had this designed when we built the house to avoid those long trips to a laundry romm which may have located next to the garage. You don't keep your clothes in the garage, so why should you do laundry there?

Post# 65532 , Reply# 4   5/5/2005 at 21:31 (6,928 days old) by DADoES (TX, U.S. of A.)        

dadoes's profile picture
Acquaintances in town here have two washer/dryer pairs. One in the 'formal' utility room behind the kitchen (GE FilterFlo pair of 1980s vintage). Another set in an alcove to the side of their master bedroom (Whirlpool washer, don't recall the dryer, may also be a GE, I don't think it was a matched pair).

Post# 65546 , Reply# 5   5/5/2005 at 23:29 (6,928 days old) by PeteK (Ontari ari ari O )        
In the garage....

petek's profile picture
Why yes of course. I could use that for when I home from a busy night of saving the citizens from all types of evils. Just toss my superhero cape and tights in the garage washer..hmmm.

Post# 65562 , Reply# 6   5/6/2005 at 03:56 (6,927 days old) by foraloysius (Leeuwarden, Friesland, the Netherlands)        
Why yes ofcourse!

foraloysius's profile picture
Here's the link to my laundry corner. It's in a corner of the bathroom, very convenient near the bedrooms!

CLICK HERE TO GO TO foraloysius's LINK


Post# 65571 , Reply# 7   5/6/2005 at 06:31 (6,927 days old) by toggleswitch (New York City, NY)        
PIC request

toggleswitch's profile picture
PeteK.


Please post self-pic in tights.


LOL
-Steve


Post# 65573 , Reply# 8   5/6/2005 at 06:39 (6,927 days old) by toggleswitch (New York City, NY)        
drain facility

toggleswitch's profile picture
Does anyone have or want a drain-hole in the floor of their laundry room? Have never seen, but seems logical.

(esp. when on 2nd story)



Hi Acerone!

Nice to see copper rather than plastic pipes!

Will you be insulating (thermally and acoustically) interior room-dividing walls?

Can I assume the dryers are to be electric? Is one or the other preferred by serious collectors?

Tks.


Post# 65581 , Reply# 9   5/6/2005 at 08:22 (6,927 days old) by jaxsunst ()        
2 washers

We've been researching building a new house. Some of the 'Southern Living' floor plans have a space for a combo or stacked in the master bedroom closet along with a built in ironing board next to it. If we go with one of those, I would love a LG combo in that space with a counter over it for a coffee bar.

Post# 65586 , Reply# 10   5/6/2005 at 08:49 (6,927 days old) by Stainfighter (Columbia, SC)        
re: Southern Living plans

stainfighter's profile picture
Jaxsunst, I like that set-up a lot too. My wife thinks I am crazy enough as it is tho' with just the one F/L Frig Gallery set we have in the traditional Laundry area. If I can land a classic Frigidaire washer for the garage I will be in heaven tho' she won't understand :-)

Post# 65590 , Reply# 11   5/6/2005 at 09:33 (6,927 days old) by roto204 (Tucson, AZ)        

roto204's profile picture
My friend has a drain hole in the center of her laundry room. It looks sleek, especially since there is no threshold on the door to the adjacent great room. However, whoever designed the floor drain steeply sloped the floor to it (good!) and made leveling the washer and dryer all but impossible to do properly (bad!).

But, in the big scheme of things, I guess I'd rather have an off-kilter tub and dry rest of the house if any mishaps should occur...

(Besides, you guys have seen my "skills" at leveling machines on even perfectly flat floors--why stop a trend?)


Post# 65592 , Reply# 12   5/6/2005 at 09:39 (6,927 days old) by retromom ()        
Now THAT'S a laundry room!

Acerone:

Boy, am I jealous! You can never have too many w/d hookups! Can't wait to see the end results!

Venus


Post# 65603 , Reply# 13   5/6/2005 at 11:29 (6,927 days old) by PeteK (Ontari ari ari O )        

petek's profile picture
Twenty or so years back a retiring friend of mine sold their house in the suburbs and moved into a highrise one bedroom condo, a tiny one at that. Plans were a lot a of traveling in a new motorhome. The condo bathroom wasn't much bigger than a walk in closet but they had the place redone, the wall behind the bathtub was knocked out into the bedroom closet so they had a large jacuzzi tub installed, a new toilet and a new vanity and sink built over top of a f/l washer and dry set, hidden behind cupboard doors. Don't remember what make the machines were but they were probably Mieles. No one would ever have known the washer/dryers were below the vanity, the added height of the counter and sink wasn't really noticeable either.The kitchen job was also amazing, the condo had only a tiny walk thru galley fitted with apt size fridge, stove. When it was done there were full sized stove, fridge and dishwasher, built in nutone food prep and the lost cupboard space was made up by new cabinets to the ceiling.

Post# 65696 , Reply# 14   5/7/2005 at 06:08 (6,926 days old) by kenmore1978 ()        
gas/electric dryer preference

"Can I assume the dryers are to be electric? Is one or the other preferred by serious collectors?"

I would think that in collecting, one couldn't be picky about gas or electric, and they perform about the same. For regular use, gas vs electric rates and/or the availability of gas service would dictate the choice. If I were collecting, I would end up with gas, since the gas service in most homes could probably support several gas dryers whereas more than 2 electric dryers would call for some heavy duty entrance service, especially if other appliances like ranges, water heating and heat-a/c are electric.

In our old house, for a test I once turned on all 5 burners, the oven and the broiler on the range, triggered the hot water heater, fired up the furnace, started the dryer, and turned on our pool heater, and there was enough gas flow to run it all through the original standard residential-type gas meter.


Post# 65746 , Reply# 15   5/7/2005 at 19:28 (6,926 days old) by toggleswitch (New York City, NY)        
Gas meters

toggleswitch's profile picture
Gas meters, BTW come in "sizes"

Mom and Dad's house had oil heat and hot water via an instantaneous coil(in the hydronic boiler). The coil was notorious for not producing enough hot water for a two family house that had three baths, two kitchens a DW and a T/L washer.

Since cooking and dryer were gas, my parents added a gas-fired storage-type water heater with a 75 gallon capacity [somewhat over-kill, but not hugely]. It was about 75,000 Btu/h (heat input) As a reference point you can heat a small house with about 100,000 Btu/h, a dryer uses 22,000 Btu/h and a stove's borners are about 12,000 Btu/h per burner. (so figure 60,000 btu/h max use.)

When all three gas-burning appliances were going the gas meter was straining and making a lot of noises. The flames on the appliances had a slight pulsing to them. By law here they get changed every so many year/decades. So it was replaced by one with a creater capacity down the road and it became silent and the pulsating flames went away.


Apparently inside there are two diaphragms that are nect to each other... as one fills it forces the gas out of the other. At a certain point there is a level in there that re-directs which "bag" is emptying and which is filling.

If anyone has a link with a pictorial as to how these work, I'd love to request it...


Post# 68644 , Reply# 16   5/30/2005 at 07:29 (6,903 days old) by toggleswitch (New York City, NY)        

toggleswitch's profile picture
Hi Acerone.

May I request pics of the finished room?


Enquring minds want to know....


Post# 68646 , Reply# 17   5/30/2005 at 08:10 (6,903 days old) by designgeek ()        

If I was buying a new dryer (or a reconditioned vintage unit) I would go for electric. Also electric water heater with solar preheating panels on the roof.

This on the basis that gas supplies may start to decline in the next five to ten years, and there'll be demand for building more nuclear & wind plants to make up the difference. Also in an earthquake, a disrupted gas line can be a serious fire hazard, but the worst that can happen to the electric supply is a regional blackout, which one can deal with by way of a diesel generator and/or photovoltaics on the roof.


Post# 68674 , Reply# 18   5/30/2005 at 18:31 (6,903 days old) by alr2903 (TN)        
why not one of each?

Nothing like gas to toast some towels and jeans. extra low on a Kitchen aid can not be beat for knit polo's and such. We live in a house that is total electric, but i miss the gas for the towels and jeans. alr2903.

Post# 68776 , Reply# 19   5/31/2005 at 12:10 (6,902 days old) by lbcarguy ()        

Hi,

Multiple laundry hookups are great. You will love it!

I have 3 hook ups in my laundry/game room off the garage. This was planned with the new construction that started last August and finished in November. I was worried what the city might say but it never came up when the inspector was out. I also have 5 220 lines in the garage and 3 gas lines. I have two gas dryers and one electric. I have a Frigidaire Flair on 220 and my air compressor is 220. I have 300 amp service, with 200 amp for the garage and 100 at the house, which is expandable to 200.

I live in a neighborhood build in 1950-52 and we had one transformer serving about 10 houses. Most had remodeled and many upped their service from 100 amp to 200. When my neighbors A/C unit kicked in, my lights/tv would dim. The electric company installed a new larger transformer for us. I should find out this summer if it cured the problem ( I am pretty sure it will).

I run all 3 washers and dryers together with no problems. You can see pictures in my photo collection. When I remodel the house someday, will add an inside laundry too, so I will have room for one more set (yeah!).

MK in LBC


CLICK HERE TO GO TO lbcarguy's LINK


Post# 68831 , Reply# 20   5/31/2005 at 21:18 (6,902 days old) by kenmore1978 ()        
capacity

I remember you were worried that your drainline wouldn't be able to carry away the water fast enough, did that work out OK?

Post# 68938 , Reply# 21   6/1/2005 at 16:37 (6,901 days old) by cleanclothes ()        
Could have saved some space

You may have been able to save some space. Speed Queen is the only brand I know of that makes a stack dryer for the home. Two dryers in the same spot as one. NICE!

CLICK HERE TO GO TO cleanclothes's LINK


Post# 69302 , Reply# 22   6/5/2005 at 11:52 (6,897 days old) by Acerone ()        

Part 2. Still a ways to go until it's all done.

Post# 69324 , Reply# 23   6/5/2005 at 18:13 (6,897 days old) by toggleswitch (New York City, NY)        
power ports

toggleswitch's profile picture
I am confused by junction boxes above, and below the water supply....


sconces above?


ah or maybe two stackable units?


Post# 69325 , Reply# 24   6/5/2005 at 18:16 (6,897 days old) by toggleswitch (New York City, NY)        
Basic plumbing- duh

toggleswitch's profile picture
Must be because the drain pipes are with the water supply tap boxes, and the silver covered things are the dryer vents..

N'est ce pas?


Enquiring minds want to know.. LOL


Post# 69353 , Reply# 25   6/5/2005 at 22:13 (6,897 days old) by toggleswitch (New York City, NY)        
Reading is FUNdamental

toggleswitch's profile picture
LOL When in doubt read the first panel /posting.


my humble apologies. LOL


Post# 69394 , Reply# 26   6/6/2005 at 09:00 (6,896 days old) by kenmore1978 ()        
sconces

Since in the first shot I don't see any gas lines, I would assume the the upper boxes are for 30 amp dryer outlets, since the lower boxes are obviously 120 volt outlets

Post# 69402 , Reply# 27   6/6/2005 at 10:01 (6,896 days old) by Acerone ()        

You got it kenmore1978....

Post# 69405 , Reply# 28   6/6/2005 at 10:32 (6,896 days old) by jaxsunst ()        

My wife thinks I'm a little batty too. I have convinced her to let me have ONE vintage washer in the garage. I'm waiting for my dream Kelvinator.

Where in Arkansas are you?


Post# 69407 , Reply# 29   6/6/2005 at 10:42 (6,896 days old) by Acerone ()        

The house is located in Benton but right now I'm living in Bryant.

Post# 69453 , Reply# 30   6/6/2005 at 18:00 (6,896 days old) by jaxsunst ()        

I am from Mabelvale, my parents still live there. My sister lives in Little Rock in the Heights.


Forum Index:       Other Forums:                      



Comes to the Rescue!

The Discuss-o-Mat has stopped, buzzer is sounding!!!
If you would like to reply to this thread please log-in...

Discuss-O-MAT Log-In



New Members
Click Here To Sign Up.



                     


automaticwasher.org home
Discuss-o-Mat Forums
Vintage Brochures, Service and Owners Manuals
Fun Vintage Washer Ephemera
See It Wash!
Video Downloads
Audio Downloads
Picture of the Day
Patent of the Day
Photos of our Collections
The Old Aberdeen Farm
Vintage Service Manuals
Vintage washer/dryer/dishwasher to sell?
Technical/service questions?
Looking for Parts?
Website related questions?
Digital Millennium Copyright Act Policy
Our Privacy Policy