Thread Number: 54680
1964 GE Dryer 1DA820Y4W
[Down to Last]

automaticwasher.org's exclusive eBay Watch:
scroll >>> for more items --- [As an eBay Partner, eBay may compensate automaticwasher.org if you make a purchase using any link to eBay on this page]
Post# 770656   7/13/2014 at 20:42 (3,568 days old) by wiskybill (Canton, Ohio)        

I got this dryer back in October 2013. It came from the original owners' estate and sat in the same place since it was installed new. Still plugged in and in use.
The right rear bottom of the cabinet was rusted thru after years of sitting next to the matching washer, which was replaced some years earlier.

Time for a cabinet transplant!

I found a 1982 model for $30 that was in pretty good shape and proceeded to strip it down for parts now that warm weather allowed.

It's all done and in service again. Almost all of the parts are original although I think the motor was replaced at some point. It looked a little newer than a 50 year old motor IMO.


  Photos...       <              >      Photo 1 of 14         View Full Size



Post# 770659 , Reply# 1   7/13/2014 at 21:01 (3,568 days old) by gansky1 (Omaha, The Home of the TV Dinner!)        

gansky1's profile picture
That's a wonderful restoration, it looks new! I remember a similar model at a house I used to babysit in, I loved that lighted panel.

I think your donor-dryer is a 72, not 82. We had the exact same (72) dryer and matching washer growing up. I have a 69 washer and matching dryer top that I'll need a donor machine for at some point, I keep my eyes on CL and one day a gassy donor will pop up.

Congrats again, great work!


Post# 770681 , Reply# 2   7/13/2014 at 22:04 (3,568 days old) by wiskybill (Canton, Ohio)        
Thanks, Greg

Here's the mod/ser of the donor, DDE5200LDWH/ML209088G

You're probably right about the year.

There were subtle differences between the two machines. The original blower housing
only matched the mounting holes on the bottom portion. New holes were drilled in the cabinet to match the top.

The mounting screws for the heater assembly. The original cabinet had mounting screws that were attached to the back of the cabinet and on the newer cabinet, the heater attached directly with sheet metal screws.

I reused the original belt tensioner. It still worked very smoothly. The newer was a slightly modified design and I've seen newer yet that were completely different.

It was a fun project to do. Now I can put my 1973 Kenmore 800 gas dryer in place
beside it and will be set for dryers.


Post# 770690 , Reply# 3   7/13/2014 at 22:26 (3,568 days old) by pulltostart (Mobile, AL)        

pulltostart's profile picture

That's a beautiful dryer - love the styling.  You did a great job!

 

lawrence


Post# 770737 , Reply# 4   7/14/2014 at 06:38 (3,567 days old) by bajaespuma (Connecticut)        
Aferim!

bajaespuma's profile picture

Inspiring work. I have three old GE dryers that I need to do the same thing to so I have a couple of questions:

What kind of paint did you use?

How did you deal with those pesky trim strips; did you leave them on and mask them, or did you remove them, paint, and then replace them?

 

Not only does your dryer look spiffy, but those old GE dryers are among the fastest, quietest and most reliable dryers ever produced.


Post# 770760 , Reply# 5   7/14/2014 at 08:22 (3,567 days old) by wiskybill (Canton, Ohio)        
Thanks, Ken

The paint is Rustoleum Appliance Epoxy in spray cans for the outer
cabinet and panels and I had a quart of the same that I used for the inside
with a brush. It dries a little slower than regular spray paint and the cure
takes more like a week, but it gives a really durable finish. If you take your time you can get good results. But, you have to use it in a well ventilated area, and wear a mask. It's a heavy bodied paint and tends to hang in the air longer. When I finished I had to wipe down my arms and legs with mineral spirits.

The trim strip at the bottom front is held by 3 clips. I was able to carefully remove them from the backside by bending the tab ever so gently so as not to break it. I removed the trim at the bottom of the control panel also to touch up the paint where some rust had begun. It's held by 2 spring clips that come off easily, but don't let them fly across the room. I looked for the first one for about an hour before I found it. The trim then slides off. I touched up the bottom of the control panel with some Testors model paint that was a good match.

I have to agree about the design of this dryer. It's simple and sturdy and easy to work on. The only new parts I bought were a fluorescent tube and starter.


Post# 770766 , Reply# 6   7/14/2014 at 08:51 (3,567 days old) by moparwash (Pittsburgh,PA )        

moparwash's profile picture
Great job!...it will last another 50 years!

Post# 770782 , Reply# 7   7/14/2014 at 10:38 (3,567 days old) by combo52 (50 Year Repair Tech Beltsville,Md)        
Restored GE Dryer

combo52's profile picture
Looks Great Bill, you are correct that a new motor was installed at some point along the line, when GE still used round motors during orignal production they were always painted grey, the lacquered colored motors were made later and were sold as a replacement motor. These were very good motors, the only problem was the small cooling openings in the ends of the motor would get blocked with lint easily.

Post# 770794 , Reply# 8   7/14/2014 at 11:25 (3,567 days old) by ultramatic (New York City)        
Beautiful job Bill!

ultramatic's profile picture

 

 

I really enjoy a restoration. Thanks for the pics!


Post# 770800 , Reply# 9   7/14/2014 at 11:44 (3,567 days old) by bluejay (Havre de Grace, MD)        

bluejay's profile picture

Beautiful job!  I love the control panel on that dryer!



Forum Index:       Other Forums:                      



Comes to the Rescue!

The Discuss-o-Mat has stopped, buzzer is sounding!!!
If you would like to reply to this thread please log-in...

Discuss-O-MAT Log-In



New Members
Click Here To Sign Up.



                     


automaticwasher.org home
Discuss-o-Mat Forums
Vintage Brochures, Service and Owners Manuals
Fun Vintage Washer Ephemera
See It Wash!
Video Downloads
Audio Downloads
Picture of the Day
Patent of the Day
Photos of our Collections
The Old Aberdeen Farm
Vintage Service Manuals
Vintage washer/dryer/dishwasher to sell?
Technical/service questions?
Looking for Parts?
Website related questions?
Digital Millennium Copyright Act Policy
Our Privacy Policy