Thread Number: 69650  /  Tag: Modern Automatic Washers
Speed queen FL mold & mildew smell
[Down to Last]

automaticwasher.org's exclusive eBay Watch:
scroll >>> for more items
Post# 925612   3/7/2017 at 23:14 by agitated (michigan)        

Hello All, found postings very informative. Had no idea laundry is so complicated.

Really torn between Speed Queen FL & TL.
I like the FL for water saving & non-agitator features--(like to be able to wash lots of down items & blankets-lots of allergies). But so pricey! and of course the fear the common FL MOLD issues.

Per SQ, their FL dont get mildew & funky smells if door left ajar after use, and that no "sanitary clean" or bleach cycles required.
Sounds too good to be true?
your experiences much appreciated please.
I dont want to end up w an expensive chunk of metal. Help!





Post# 925624 , Reply# 1   3/8/2017 at 04:02 by brucelucenta (tulsa, oklahoma)        

brucelucenta's profile picture
Both machines are supposed to be very good and well built. I think it is just a matter of which type machine you prefer. I personally have switched to front loading machines because they are easier on the clothes and you have virtually NO linting or wear on your clothing. It also spins out the clothes better and takes less time to dry.



This post was last edited 03/08/2017 at 05:03
Post# 925631 , Reply# 2   3/8/2017 at 05:30 by Easyspindry (Winston-Salem, NC)        
I came home from . . .

. . . the Beltsville, MD wash-in with a SQ front loader. I love it. It's quiet and washes great. When you choose HOT water, that's what you get. It spins out almost all of the water, and the clothes are practically dry when it's finished.

True, it's been only since last August, but I am impressed with the machine. I leave the door open (ajar) when not in use and have never had any mold smell.

I, too, was afraid of the price. But it's paid for now and I'm very happy with it.

Jerry Gay


Post# 925632 , Reply# 3   3/8/2017 at 05:33 by Easyspindry (Winston-Salem, NC)        
Addendum . . .

Some years ago, I had a Whirlpool Duet set -- FL. Left the door ajar and never had a mold problem. Had that machine for 10 years. The washer was better than the dryer.

Jerry Gay


Post# 925633 , Reply# 4   3/8/2017 at 05:39 by qualin (Canada)        

I've had a Speed Queen (aka Huebsch) front loader since 2011.

I always make sure to leave the door ajar and the detergent drawer open after every load. I've never had a problem with mold or mildew, but then again, I live in a very dry climate, especially in winter.

The other trick I've found is to make sure that you occasionally ensure that you do hot water washes and keep fabric softener use to an absolute minimum.. and when you do use it, always use it with a warm water wash, never with a cold one.

My wife loves to do cold water washes, which makes the washer smell a little funky if she does a lot of them in a row. I think this is a side effect of HE style washing and is pretty much unavoidable with any FL machine. The solution to that is to pour about an 1/8th of a cup of bleach into the tub, then do a hot water wash without any clothing in the tub. That always fixes the smell.

Just for the record, when I did have a top loader, it also suffered from the same problem when it came to cold water washes, but it needed an entire cup of bleach to get rid of the smell.


Post# 925634 , Reply# 5   3/8/2017 at 06:32 by littlegreeny (Milwaukee, WI)        

Since we are on the subject, I also have a few questions about SQ front loaders. Does it also have a true hot fill on the Normal Eco cycle? And does it fill based on load size or is it a timed fill? There seems to be a lot of conflicting info on that.

Post# 925639 , Reply# 6   3/8/2017 at 07:25 by Lorainfurniture (Cleveland )        

Definitely go with front load.

I just happened to list my like new set for sale, and I'm not terribly far from you

www.automaticwasher.org/cgi-bin/T...


Post# 925644 , Reply# 7   3/8/2017 at 08:20 by agitated (michigan)        

thank you all so much for your prompt input. so happy to find this forum!
SQ was so emphatic that their FL dont get this problem,.. always worry me when they say "never"

Have seen so few posts re SQ FL; horrid tale of one from this forum w leaks/low water- suffered 2 yrs to get SQ to exchange it to TL.
Countless happy TL owners. Versus little written about FL.
Store near me doesnt even have FL on floor.

DH balking at $ and WP Duet fiasco ( i didnt know cold wash was not good thing!) He's pushing for new HE TL, which all sound like junk & prob make me slave to 2-hr cycles while it tries to fix "load imbalance". Tho i know 2 families w Maytag Cenntenials who seem pleased.

Am still favoring SQ FL...


Post# 925693 , Reply# 8   3/8/2017 at 14:15 by agitated (michigan)        

SQ Rep said dont have mold issues & no bleach or "routine maintainance" cycle because of special spin design?

Post# 925702 , Reply# 9   3/8/2017 at 15:19 by kb0nes (Burnsville, MN)        

kb0nes's profile picture
The only advantage a SQ FL machine may have over any other is that the outer tub is stainless instead of plastic like most every other machine out there. There 'might' be some advantage to stainless as far as having biological growth on the surface.

But in any case, if you use a good detergent in proper quantities, wash in hot water at least some of the time, use bleach once and again and leave the door open when not in use, any front load machine will stay odor free. If a front load washer gets smelly, the users habits caused it.

Over in Europe the majority of washers are front load machines, the people over there don't seem to have funky smelling washers. Here in the US where people used their poor laundry habits left over from their top load machine in their new front loader, they ended up with smelly washer syndrome. Then instead of learning how to correct their error, they go and sue the manufacturers. Clearly the machine is the problem, "I know how to do laundry" lol


Post# 925707 , Reply# 10   3/8/2017 at 15:55 by Yogitunes (New Jersey)        

yogitunes's profile picture
bottom line.....with ANY machine....

if there was an issue caused by the machine or its function, production would have stopped...

and ALL of the machines would have it....

there has to be something to the fact, some of us:

DON'T have a 'clean washer' cycle on our machines...nor a reason to use/need one

DON'T wash in cold water for every single load...

DON'T leave the door open...

DON'T leave the dispenser drawer open...

DON'T have to do any special wipe down or maintenance....

I never had to, and never will.....


in fact, any used machine we get in that is scummed up, mold/mildew issues, bad odors.....those issues clear up after several uses....and are never seen again....

it's as simple as that......



Post# 925712 , Reply# 11   3/8/2017 at 16:44 by golittlesport (California)        
mold is caused by user error

I don't believe smelly front load washers are as common as one might think. And I also believe that any that are moldy are caused by user error -- cold water only washes, too much fabric softener and not letting the machine air out and dry after use.

I've had front loading washers since the year 2000 and never experienced mold or smells. I have many friends and family members who also have front load machines and never have a problem. In fact, I personally do not know anyone who has.

Some crafty lawyers got together a class action suit of people who did not follow the directions that came with their washers and sued a few manufacturers. That made the news and created the mold hysteria out there.


Post# 925716 , Reply# 12   3/8/2017 at 17:09 by whirlykenmore78 (Prior Lake MN (GMT-0700 CDT.))        
Go for the SQ FL

whirlykenmore78's profile picture
I have had mine almost a year now and am quite happy with it. It is a very well made machine and is much faster than other machines. Also if you do have a problem it is easier to fix than many others.
WK78


Post# 925723 , Reply# 13   3/8/2017 at 17:56 by washerdude (Canada )        

Front loaders are the way to go nowadays, before switching to a FL i owned a WP DD top load for 14 years. I was skeptical at first, but our new two year old FL cleans better than our old machine ever did.

Post# 925725 , Reply# 14   3/8/2017 at 18:08 by whirlykenmore78 (Prior Lake MN (GMT-0700 CDT.))        
Agreed Washerdude:

whirlykenmore78's profile picture
I was a staunch WP DD man until I got my SQ FL. I wouldn't go back.
WK78


Post# 925931 , Reply# 15   3/10/2017 at 02:52 by askolover (South of Nash Vegas, TN)        

askolover's profile picture

I've had a FL since 1997 (and it's still going) and have never had any issue with mold either.  Like the others have said, if it were a manufacturer problem they would ALL have mold issues.


Post# 925957 , Reply# 16   3/10/2017 at 06:26 by qualin (Canada)        

Here's the other problem...

Whirlpool once designed a machine with an outer tub not only made out of plastic, but with lots of crevices and spots where gunk could accumulate. (Picture shown below.)

In almost every video I've seen where the tech is doing a bearing replacement, the back of these tubs are absolutely filthy with gunk and residue. This could be what causes the majority of moldy smells in these machines.

So, why all these crevices? They're there to give the plastic strength so it actually is firm enough to hold the form it needs to, because obviously using thicker plastic was too expensive, I'm guessing.

So yeah, SQ machines, having a stainless outer tub, don't need anything to give the steel more strength, so no crevices to trap gunk.

I'm not sure if newer Whirlpool machines now have a smooth rear now, but it would make sense that they learned from this engineering mistake.


CLICK HERE TO GO TO qualin's LINK


Post# 925962 , Reply# 17   3/10/2017 at 06:43 by askolover (South of Nash Vegas, TN)        

askolover's profile picture

the Frigmore my neighbor gave me a few years ago had that same tub back in it.  But hers wasn't gunked up...she must have used hot and warm washes frequently.  Stainless steel is one of the many reasons I own Asko and Miele machines, plus the fact that the massive behemoths we have now won't fit in my laundry closet.


Post# 925963 , Reply# 18   3/10/2017 at 07:01 by combo52 (Beltsville,Md)        
Plastic Outer Tubs In FL Washers

combo52's profile picture

Are all filled with ribs for the etra strengh needed for them to work.

 

The plastic outer tubs and the cheaper concrete ballast weights that most FL washers use limit their maximum life spans a lot, Speed Queens SS outer tubs and cast iron ballast weights allow their FL washers to last over 25,000 loads before they start to have serious fatigue issues.

 

We are about to change out two SQ stack washer-dryers at a famous hotel in Washington DC next week that are 5 and 6 six years old, and have been used about 20 times a day so each of them has washed and dried between 30,000 and 40,000 loads each, and after a little refreshing we will likley resell both pairs, neither washer has ever had new bearings, new motors or either the control or motor circuit boards replaced.

Both washers have had new inlet valves, new door boots, start switches and a few knobs replaced. The dryers have had a roller or two replaced, one motor and a temp switch and a timer and a few knobs between the two, not even a heating element in either because they are being operated on 208 volt power instead of 240 volts.

 

John L.

 

 


Post# 925969 , Reply# 19   3/10/2017 at 07:13 by Logixx (Germany)        

logixx's profile picture
My grandma has a Miele washer - the outside of the drum is coated with stinky yellow sludge that even a boil wash with citric acid didn't touch.

My Duet has a platic outer drum and it's pristine.

So to me, it all comes down to proper usage.


Post# 925970 , Reply# 20   3/10/2017 at 07:16 by Gyrafoam (Roanoke, VA)        

One advantage the Europeans have is the ability to seriously boost water temperature.

I bought a new FriGEMore in 1997. It's low mileage and having been dropped to free-fall down a flight of stairs when only a few months old, is tough as nails. No repairs.
Just a dent on the rear console.
I have never had mold or odor issues with it, although the dispenser drawer requires regular cleaning.
I also tend to wash everything in hot water, and always leave the door ajar after use.

I've never known anyone with a SQ front loader that had mold or odor issues, so they must be doing things right.


Post# 925973 , Reply# 21   3/10/2017 at 07:40 by mrb627 (Buford, GA)        
@JohnL...

mrb627's profile picture
John,

It would be interesting to see a couple pictures of these trade in machines when you get them back in the shop. Please post, if you can...

Malcolm


Post# 925980 , Reply# 22   3/10/2017 at 08:09 by Yogitunes (New Jersey)        

yogitunes's profile picture
heres a Neptune inner drum after a tear down....hot/warm washes, bleach with the whites....this was at 14 years of service....

  View Full Size
Post# 925997 , Reply# 23   3/10/2017 at 10:05 by johnb300m (Chicago)        
tub access envy (off topic)

johnb300m's profile picture
I envy you all who can open your tubs on older front loaders.
It's come to my attention that Whirlpool's new direct drive FL architecture (MT WP) have glued/sealed tub halves.
They're only sold as a $700 assembly.
NO access to the spiders. Or the bearings. It's all sealed now. >:[

It's one of the reasons I BOUGHT a Maxima in the first place, after seeing all the relatively easy bearing changes that could be done on the older Duets and Epics. I never would've minded swapping out bearings every several years if I got a nice solid washer in other aspects.
Not anymore. And I'm peeved. These bearings better last.


CLICK HERE TO GO TO johnb300m's LINK


Post# 926004 , Reply# 24   3/10/2017 at 10:32 by Yogitunes (New Jersey)        

yogitunes's profile picture
I caught that sealed tub machine while stumbling upon a yoututbe vid of a guy who was able to get around that sealed tub....and repair his machine.....apparently, it can be done...







Post# 926021 , Reply# 25   3/10/2017 at 13:18 by johnb300m (Chicago)        

johnb300m's profile picture
yeeeeesh, that looks like a looooot of trouble.
But doable..... :/


Post# 926198 , Reply# 26   3/11/2017 at 08:43 by Rolls_rapide (Scotland, UK)        
Sealed Tubs

rolls_rapide's profile picture
The reason for the sealed tubs is to "encourage" new sales.

That way, the bearings wear out, the consumer baulks at the cost of renewing the drum-tub assembly (where parts are available), the consumer considers other aged components (suspension, electronics, etc.), and the consumer ultimately decides (actually, they don't decide, they're forced) to buy a new machine.

And the new machine will have all these lovely gimmicky 'bells and whistles', but sadly will not be built to last any length of time - even less than the machine which preceded it.

Meanwhile, the rubbish pile gets bigger...

The whole situation is dire. In fact, it is a complete crock of shit.


CLICK HERE TO GO TO Rolls_rapide's LINK


Post# 926200 , Reply# 27   3/11/2017 at 09:09 by washerdude (Canada )        
Sealed Tubs

The tub on the newer WP FL's are not 100% sealed. They use the same tub clip method of attaching the two half's of the tub just like on the older duets. I'm sure if bearings failed, you could always use high quality Nachi bearings. But at the same time, they don't sell the god damn spider or tub seal, however I'm assuming you could get away with a non OEM seal too...spider seems to be a one time deal only...

Post# 926234 , Reply# 28   3/11/2017 at 14:26 by mark_wpduet (Lexington KY)        
The old Duets engineering mistake?

mark_wpduet's profile picture
Not if you do laundry properly and leave door and dispenser open. I have an OLD duet that is 12 yrs old next month, and never had a trace of mold or smells. This is the case with all FL washers. They won't smell if you do these things *UNLESS* something is drastically wrong with the washer.

Post# 926238 , Reply# 29   3/11/2017 at 14:40 by mark_wpduet (Lexington KY)        
Oh forgot to add

mark_wpduet's profile picture
It does piss me off when I see manufacturer's touting energy savings and being eco friendly - (like that article above said) but, in reality, it's just the opposite! If people are throwing out double the amount of laundry appliances than they once were and paying for new ones, there's nothing eco friendly about that at all. I've been so lucky with my machine and I hope it lasts me a few more years at least. I wonder if the total cycle count on my Duet is lower than average? I'm thinking an average of 4 loads per week, usually rather large loads - sometimes a little more, sometimes less, so say 20 loads per month to be safe - at 12 years old, that would mean my duet has only done around 2,880 cycles. Just say 3,000 to be safe. Where other families do laundry DAILY! MUCH MUCH MORE. That could be part of the reason I've been so lucky.

Post# 926255 , Reply# 30   3/11/2017 at 16:03 by Yogitunes (New Jersey)        

yogitunes's profile picture
people way of thinking surprises me....

do you think dishwashers would have the same issues if only COLD water was used?...we don't leave those doors open or anything!....stacking dishes in there until a full load is met, so odors can happen, but once we run a cycle, that is all gone....

where is the true thought in energy savings.....running a load several times to get the clothes clean?....running an empty machine, completely filled with HOT water to clean it?.....or, wash in cold water to save our clothing from fading or shrinking, and yet most will toss them into a 160 degree dryer, way hotter than most water heater settings....

were not asking for every fill to be hot water.....just the first wash...and what does that equal, 3 to 4 gallons tops!

seems like simple practices like hot/warm washes.....will eliminate having a mold/mildew issue, eliminate running a clean washer cycle, and most likely less break down time or replacement of a machine....

amazing how many people will never understand any of this....seems like a lot of people just want to complain, they don't want the cause, the answer, or the fix!

how many threads have and/or will we see on this subject?





Post# 926261 , Reply# 31   3/11/2017 at 17:15 by whirlykenmore78 (Prior Lake MN (GMT-0700 CDT.))        
Cold washing bullshit:

whirlykenmore78's profile picture
I never have and never will do cold washes. Cold water is for RINSING hot water is for WASHING. Nuff said.
WK78


Post# 926276 , Reply# 32   3/11/2017 at 19:19 by washerdude (Canada )        

I've heard people recommend to wash whites in cold water...YUCK! No way that's ever going to happen at our house.

Post# 926314 , Reply# 33   3/11/2017 at 21:59 by kb0nes (Burnsville, MN)        

kb0nes's profile picture
"The reason for the sealed tubs is to "encourage" new sales. "

I really don't believe that this is true. The reason manufacturers might switch to a sealed tub would be for manufacturing cost savings and less likely hood of a leak.

Consider these things:

The main bearing and shaft seal really don't fail that often, especially if the machine is used correctly.

When confronted with a malfunctioning machine that is say 5 or 6 years old, what percentage of owners even bother to consider servicing the machine??

Of that small percent of people that would call for service, only a tiny percent of them will choose to replace the main bearing and seal if that were the failure. Even in a non-sealed tub machine we are talking a $500 repair, most are condemned at this point.

So looking at those factors, a sealed tub really means nothing different will happen. Five year old machines that need bearings will be scrapped either way. Us appliance aficionados that believe in repair no matter what are few and far between. Sure it is an annoyance for us, but it really won't force more sales by way of planned obsolescence.

I too would LOVE to return to times where machines were repaired and not replaced anytime they fail. But I'd also like to return to the times where NOBODY drank bottled water!!! In the grand scheme of things, single use plastic bottles are FAR worse for the environment then disposable appliances, even if they are properly recycled.


Post# 926316 , Reply# 34   3/11/2017 at 22:11 by Pierreandreply4 (St-Bruno de montarville (province of quebec) canada)        
thats the problem these days

pierreandreply4's profile picture
i can say thats clearly a problem if it was not for my aunt also my mom aunt for keeping the bill and sale paper for her 6 year old fridge that she had to call for a repair a couple of years ago the tech would of told her to replace her fridge i think the same go for washers and dryers, picture is an exemple there was a time where appliance could last up to 40 years and where easy to repair and also unless you can repair the machine yourself and have good experiance the trouble with modern machine they make them so that after 10 years or more of service the customer trying to get a call for a repair have to buy a new machine because depending on the tech they rather advise replacement than repairing the washer that is sad

  View Full Size
Post# 926367 , Reply# 35   3/12/2017 at 10:28 by combo52 (Beltsville,Md)        
Sealed Outer Tub assemblies On New FL Washers

combo52's profile picture

Are probably a good cost saving idea on FL washers with cheap plastic outer tubs. A sealed tub assembly will save many machines getting junked early because of leaking outer tub seam seal leaks.

 

Also keep in mind FL washer bearings almost never fail unless water gets past the main seal and ruins the bearings.

 

Bearing life is not affected by spin speed, load size, even the amount of use the washer gets to a measurable degree.

 

The main issue if you want to replace the bearings in any FL washer is making sure that the main seal assembly is in perfect condition, ultra premium SS bearings etc will not make any difference in life, SS sealed bearings will not work any longer if exposed to water and detergent.

 

If you want a reparable washer that has the potential to last 30+ years today there is ONLY one reasonable choice for the average home, A Speed Queen FL Washer.

 

John L.


Post# 926379 , Reply# 36   3/12/2017 at 12:49 by Stricklybojack (San Diego, CA)        

stricklybojack's profile picture
.
In regards to mold, we have kept the door ajar on ours and had no problems however you MUST wipe the black rubber tub seal regularly as water/moisture hides there and gets nasty fast.

The SQ FL is chock a block full of very expensive parts that will never make it to the 30 year mark.
I can't make it to 30 loads per $600 motor board on mine...no exaggeration.
FL washers are only as good as the electronics that run them and SQ's are made in Mexico and prone to failure sooner or later...but not 30 years later by a long stretch.
FL machines are disposable devices at this point, if you choose SQ I implore to get the models with a 5 year warranty. That said, be aware you can easily replicate this warranty on other brand machines through third party consumer insurance vendors.
I used to love my SQ on the ocassions it worked...but now feel oh so suckered by the 30 year BS after it started breaking on a nearly monthly basis.
Reviewed.com calls them a "cult washer" brand, meaning for drinkers of the kook-Aid only, in all measurable areas they woefully underperform for the price.

Yes the TL machines are much beloved but the FL design is new as of two years ago and is very thinly distributed to home owners compared with what a consumer behemoth like Whirlpool puts out. Meaning it takes much longer to teethe through the design/manufacturing bugs via the feedback loop with the installed base of customers. To paraphrase an old car joke, Whirlpool looses more consumer FL washers than SQ makes.

Yes I may have been "unlucky" with my machine but don't buy a FL machine based solely on considerations like stainless tubs and what not cause it's just a better arrangement of deck chairs on a washer Titanic that is skippered by questionable quality control in a sea of electronic icebergs....ahem, imo.
And btw, even on the sturdy-build-front the SQ is weirdly flimsy in very conspicuous places, like the door and the start button (I have the rear control "knobs" model), to name two big ones for me. Every time I use it I think, "really, of all the start buttons you could have picked." I then wonder, "just to save how many cents?". Same with the door, it just feels chintzy.




This post was last edited 03/12/2017 at 14:32
Post# 926385 , Reply# 37   3/12/2017 at 13:16 by Pierreandreply4 (St-Bruno de montarville (province of quebec) canada)        
lots of factor comes in when it comes to front load washers

pierreandreply4's profile picture
well there are alot of factors that comes when deciding to buy a front load thats what i have right now but not closing the door eather on going back to a good old fashion top load washer,

1 capacety of the washer for the wash drum

2 cycle needed and wash time for the load

3 years of use right now i have a 13 year old whirlpool duet washer dryer set going on its 14 year of use this summer no repairs on the washer only a service cleanup on the dryer because of to much lint but there will come a time when they will need to be replace and the big question is do you went to spend time having a tech because the washer is defective since day 1 if it would of been the case mny mom and i would of ask the store where we purchuse or whirlpool duet to exchange the model on day 1 there are alot of factors to think of but the main point of my post is depends on how many load per weeks or days the washer will be use.


Post# 926388 , Reply# 38   3/12/2017 at 14:06 by mark_wpduet (Lexington KY)        
Pierre

mark_wpduet's profile picture
Your duet is older than mine. I know back then they were built in Germany - Maybe that's why? LOL. Why do I get the feeling that we will not be so lucky with our next set? Then again, I said the same thing about this set when I got it. I thought in 2005 there would be NO way I would still have this machine continuing to work in 2017

@ agitated - Some real disagreements in this post regarding SQ longevity. Personally, I've never had a SQ but I'm sure their machines are built much better than WP or LG/Samsung, GE, etc. I think you have been unlucky and just gotten a hold of a really buggy machine where something is wrong somewhere. What surprises me most is that they won't replace the thing (especially at this point), which is kind of a turn off and shocking since they are so expensive.


Post# 926453 , Reply# 39   3/12/2017 at 21:41 by Pierreandreply4 (St-Bruno de montarville (province of quebec) canada)        
mark_wpduet

pierreandreply4's profile picture
thank you mark_wpduet my secret is for 1 thing thanks to this site i have seen the light and now wash light color heavy duty using hot water heavey duty cycle colors warm water but my secret is i do not neglect doing a monthly cleanup using eather tide clean regular bleach white cycle or just water let the washer run a full cycle empty and it cleans it using hot water of course so far doing my home work when after chrismas my mom and i had to replace the dishwasher while in the store i have look at the speed queen topload model awn432 and its matching dryer would use the same pattern sure its a top load but my mom and i have not close the door on buying frontload because in the long term we went a stack set and stack the dryer on top the washer but doing that means costly renos but its good to have options thats the set i have look and i like the old fashion timer knob but not du to be replace yet but if my mom and i have to since i am the one doing the laundry for my mom and i speed queen would be my number1 choice

  View Full Size
Post# 928586 , Reply# 40   3/23/2017 at 21:22 by agitated (michigan)        

Thanks to all who have posted re my question re Speed Queen. I took a leap & got the SQ FL, awesome looking machine. DH is engineer & says sturdy material w expensive fasteners.


Delivery/installation not so stellar. I didnt realize till reading manual later that shipping bracket/screws should not be removed till after washer in place, not while on my driveway. And hardware should be kept for future moves. Installer may not have locked the legs. And front legs seemed off 1/8 inch.

Very nervous after reading Strickybojack's ordeal w FL. Dealer/service/Speed Queen did not shine. fingers crossed..





Forum Index:       Other Forums:                      



Comes to the Rescue!

The Discuss-o-Mat has stopped, buzzer is sounding!!!
If you would like to reply to this thread please log-in...

Discuss-O-MAT Log-In



New Members
Click Here To Sign Up.



                     


automaticwasher.org home
Discuss-o-Mat Forums
Vintage Brochures, Service and Owners Manuals
Fun Vintage Washer Ephemera
See It Wash!
Video Downloads
Audio Downloads
Picture of the Day
Patent of the Day
Photos of our Collections
The Old Aberdeen Farm
Vintage Service Manuals
Vintage washer/dryer/dishwasher to sell?
Technical/service questions?
Looking for Parts?
Website related questions?
Digital Millennium Copyright Act Policy
Our Privacy Policy