Thread Number: 66217  /  Tag: Vintage Automatic Washers
Well I'll Be.......
[Down to Last]

automaticwasher.org's exclusive eBay Watch:
scroll >>> for more items --- [As an eBay Partner, eBay may compensate automaticwasher.org if you make a purchase using any link to eBay on this page]
Post# 888126   7/4/2016 at 21:12 (2,851 days old) by vintagekenmore (Spokane, Washington)        

After four years of reliable service my Kenmore 90 series decides to bite the dust tonight with a full load of clothes and a tub full of water....it started agitating just fine and all of a sudden made a loud CLUNK...stopped agitating and now just makes a noise like gears grinding on gears...it is one of the Direct Drive machines....it wont spin either....I did get the water drained out of the tub so now Im in the market for another washer...I shouldnt complain,I only paid 200 for the set used when I bought them. But of course it goes out AFTER I pay bills and in between pay days.....GRRRR. Serial number is 110.22912101. Probably not worth repairing either....oh well




Post# 888128 , Reply# 1   7/4/2016 at 21:26 (2,851 days old) by toploader55 (Massachusetts Sand Bar, Cape Cod)        
Oh Boy...

toploader55's profile picture
Sorry to hear that.

Now you can find a Nice Belt Drive : )


Post# 888129 , Reply# 2   7/4/2016 at 21:36 (2,851 days old) by DADoES (TX, U.S. of A.)        

dadoes's profile picture
 
Probably not worth repairing either....oh well
The problem could be simple as replacing the motor drive coupler.  ~$20 part and 30 mins.


Post# 888155 , Reply# 3   7/5/2016 at 03:38 (2,851 days old) by washdaddy (Baltimore)        
I agree with DADoEs

I'd take the time and check the coupler to make sure it isn't the cause of your problem.

It's easy enough to check and doesn't take a lot of time.

If it is the problem and you replace the coupler which isn't expensive the machine could last you quite a few more years.


Post# 888156 , Reply# 4   7/5/2016 at 03:39 (2,851 days old) by washdaddy (Baltimore)        
I agree with DADoEs

I'd take the time and check the coupler to make sure it isn't the cause of your problem.

It's easy enough to check and doesn't take a lot of time.

If it is the problem and you replace the coupler which isn't expensive the machine could last you quite a few more years.


Post# 888159 , Reply# 5   7/5/2016 at 03:55 (2,851 days old) by brucelucenta ()        

The direct drive machines are pretty durable and what you have described sounds like it is only the coupler between the motor and the transmission. It certainly would be worth checking out, it is fairly simple to replace and could give you many more years of service. You certainly won't find another machine like that when you go to buy a new one.

Post# 888163 , Reply# 6   7/5/2016 at 05:28 (2,851 days old) by DaveAMKrayoGuy (Oak Park, MI)        
The one repair our M-M 90 needed:

daveamkrayoguy's profile picture
There was a small shaft in our Kenmore 90-series washer that was the one repair it needed, so far, and the repairman went as far ahead to show me how to open the cabinet and to use a small, narrow dowel to remove the old part, and install the new one...

He, of course made it known to how easy these Whirlpool and Kenmores are to fix and that there are plenty of parts available to this day!

When the in-laws moved away earlier this year they tried to foist their fairly-low line Speed Queen washer and dryer set on us... I'll leave it at that...



-- Dave


Post# 888198 , Reply# 7   7/5/2016 at 09:23 (2,851 days old) by vintagekenmore (Spokane, Washington)        

Well I had the machine checked out, and when they took the front off of it, I had a nice little puddle of oil up under the machine. So my next question, do I fork out the dough to have it fixed, or should I find myself a good ole belt drive? I honestly cannot complain about the service the machine gave me, the only little hiccup it ever had is that sometimes when it went into neutral drain, it would kick into spin as well. And when it finished the drain portion, it would do its brief pause and kick into the normal spin cycle

Post# 888203 , Reply# 8   7/5/2016 at 09:40 (2,851 days old) by Volvoguy87 (Cincinnati, OH)        
Whirlpool DD repair.

volvoguy87's profile picture
Whirlpool DD machines are pieces of cake to repair and usually worth it too. You can swap out a drive coupler and transmission in no time. Putting on a new clutch at the time is a piece of cake as well. I'd say to pony up the money for the parts and fix it. There are lots of YouTube videos which show how to do these repairs.

Dave


Post# 888312 , Reply# 9   7/5/2016 at 20:52 (2,850 days old) by kenwashesmonday (Carlstadt, NJ)        

Whirlpool direct-drive machines catch a lot of hell on the forum, but they are usually a piece of cake to repair.

Post# 888413 , Reply# 10   7/6/2016 at 14:06 (2,850 days old) by norgeway (mocksville n c )        
I personally

Would not trade a belt drive for a hundred direct drives!

Post# 888416 , Reply# 11   7/6/2016 at 14:51 (2,850 days old) by DaveAMKrayoGuy (Oak Park, MI)        
Direct-Drive Heaven: The NEW Industry Standard!

daveamkrayoguy's profile picture

As I've said, gimme "ordinary since the time appliances were painted White", "Everyday Almond", "Dull Beige", "OK in Black" or "Boring Biscuit"...

 

I did NOT want to get my in-law's Speed Queens from the same vintage era foisted on me, and without the fewer featured that MINE have, let alone the fact, that those machines would'a been well-worn out--and we would'a had'a re-do the DC outlet because the dryer is ELECTRIC!--before we'd gotten any kind'a good use outta'em and it would be just plain too late to retrieve our GREAT Kenmore (even if they are just Ken-More) machines (yes, see my post in the "How Many Loads Per Week" thread) someone else could have the life-long privilege of owning...!

 

 

-- Dave


Post# 888459 , Reply# 12   7/6/2016 at 21:17 (2,849 days old) by pumper (SE Wisconsin)        

pumper's profile picture
A new transmission runs upwards of $200+.

Post# 888480 , Reply# 13   7/7/2016 at 01:39 (2,849 days old) by Stan (Napa CA)        
For $20.00

stan's profile picture
You could fix the coupler and run it til it quits. Or fix both.
If you crack the trany open to replace the neutral drain pac (another inexpensive part) your going to be resealing (stoping the oil leak)
Machine will probably run for years.
A Freind of mine has a 1994 Kenmore, she bought used. I've replaced the tub seal, pump, agitator dogs, lid switch, coupler..I look for her old machine to outlast another freinds new front loader!



Forum Index:       Other Forums:                      



Comes to the Rescue!

The Discuss-o-Mat has stopped, buzzer is sounding!!!
If you would like to reply to this thread please log-in...

Discuss-O-MAT Log-In



New Members
Click Here To Sign Up.



                     


automaticwasher.org home
Discuss-o-Mat Forums
Vintage Brochures, Service and Owners Manuals
Fun Vintage Washer Ephemera
See It Wash!
Video Downloads
Audio Downloads
Picture of the Day
Patent of the Day
Photos of our Collections
The Old Aberdeen Farm
Vintage Service Manuals
Vintage washer/dryer/dishwasher to sell?
Technical/service questions?
Looking for Parts?
Website related questions?
Digital Millennium Copyright Act Policy
Our Privacy Policy