Thread Number: 78807  /  Tag: Wringer Washers
Maytag 32 wringer activation
[Down to Last]

automaticwasher.org's exclusive eBay Watch:
scroll >>> for more items --- [As an eBay Partner, eBay may compensate automaticwasher.org if you make a purchase using any link to eBay on this page]
Post# 1027945   3/25/2019 at 07:50 (1,830 days old) by koda (Evansville)        

Hello,

I have the job of selling off a couple late relatives' homes and the last thing remaining in my great aunt's basement is my great grandmother's washer.

From what I can tell, it appears to be a Maytag Gyratator Model 32. It is in restorable condition, the power cord is old and cracking, but the motor does run nicely. The agitator mechanism does work well, although the aluminum agitator itself does scrape a little on the base.

I cannot seem to make the wringer work. I am able to unlatch the flapper with the Maytag roller and separate the two rollers. The black roller in the top rolls freely. The bottom roller seems to rotate about 270 degrees, then a tab on the shaft stops rotation. I cannot find how to engage the wringer drive.

There is a large single wire going to the frame as a ground, I think, that is loose on the other end.

My desire to keep it is outweighed by my need to not accrue too much stuff, and it will be sold after I figure out the wringer, and get it out of the basement.

If you all could advise me on the wringer and anything else you think I should note, I will do your recommendations, then sell this thing in the next few months.

Thank you.





Post# 1027982 , Reply# 1   3/25/2019 at 16:27 (1,830 days old) by bradross (New Westminster, BC., Canada)        
I have a Model 32 -

bradross's profile picture
Without seeing a photo (or better yet, video) of the wringer, it's a little hard to determine the issue. However, it sounds like "the tab" you're referring to is the cam for the water diversion plate. If it's made of bronze with a split in the ring around the shaft, then that's what it is. It could be bound due to corrosion and/or hardened grease.

The top tension bar should just lift up to separate the rolls, unless the bearing hangers on the side are rusted and bound. Take a few pics and perhaps I can help you more advice. I've completely restored 5 of these machines thus far.


Post# 1027990 , Reply# 2   3/25/2019 at 17:49 (1,830 days old) by koda (Evansville)        

Ok. It will be a few weeks before I get back up there.

Does the roller run all the time when the motor is on or is there some activator like there is for the agitator?


Post# 1028030 , Reply# 3   3/26/2019 at 08:32 (1,829 days old) by bradross (New Westminster, BC., Canada)        
Here's a photo of the wringer control lever...

bradross's profile picture
for two different models. The one with the red release bar on top is the Model 32, and the other is a Model 30. Which one is yours?

  Photos...       <              >      Photo 1 of 2         View Full Size
Post# 1028036 , Reply# 4   3/26/2019 at 13:24 (1,829 days old) by koda (Evansville)        

It is a model 30.

Post# 1030639 , Reply# 5   4/23/2019 at 12:24 (1,801 days old) by koda (Evansville)        

Here are some pictures, please advise.

  Photos...       <              >      Photo 1 of 10         View Full Size
Post# 1030659 , Reply# 6   4/23/2019 at 19:23 (1,800 days old) by bradross (New Westminster, BC., Canada)        
Wringer control lever - dual purpose...

bradross's profile picture
It engages the wringer rolls in either forward or reverse, and then when pressed down, releases the index pin to allow the wringer to swing into various positions (when using rinse tubs behind, for example.)

The machine looks rough (cosmetically), but I've restored worse to beautiful "show room" condition. If you're thinking of keeping it, I'd suggest cleaning out the wringer head (gear box) of old grease and replacing with NLGI Grade 2 grease.

At 2:23 in the video link, you can see the various components of the wringer head disassembled. Hope it helps!


CLICK HERE TO GO TO bradross's LINK


Post# 1032555 , Reply# 7   5/13/2019 at 12:39 (1,781 days old) by koda (Evansville)        

The washer fully functions. The wringer handle does allow position rotation, and the wringer does work in both directions. I wrung out a wet sock and it did it well.

I have no place to keep this old workhorse and no real need for it. I did take the two giant porcelain washtubs already to my house and installed them, so I do the really filthy stuff there before a modern washer. I will probably see if someone local wants it, or it may go with the house.

Thank you for the advice.


Post# 1034582 , Reply# 8   6/5/2019 at 15:39 (1,758 days old) by Tinkerbell41967 (WEED)        
Gyrator post Frozen

Can anybody out there explain to me how to get the gyrator post out my seized up and I can't figure out how to get it out and this is after I did all the work and we finished it and all that and I use it on a daily basis but now it's seized upup

  View Full Size

Forum Index:       Other Forums:                      



Comes to the Rescue!

The Discuss-o-Mat has stopped, buzzer is sounding!!!
If you would like to reply to this thread please log-in...

Discuss-O-MAT Log-In



New Members
Click Here To Sign Up.



                     


automaticwasher.org home
Discuss-o-Mat Forums
Vintage Brochures, Service and Owners Manuals
Fun Vintage Washer Ephemera
See It Wash!
Video Downloads
Audio Downloads
Picture of the Day
Patent of the Day
Photos of our Collections
The Old Aberdeen Farm
Vintage Service Manuals
Vintage washer/dryer/dishwasher to sell?
Technical/service questions?
Looking for Parts?
Website related questions?
Digital Millennium Copyright Act Policy
Our Privacy Policy