Thread Number: 81191  /  Tag: Modern Automatic Washers
Speed Queen top load washer spins but does not agitate
[Down to Last]

Cool Washer Stuff on Amazon:
scroll >>> for more items
Post# 1052102   11/23/2019 at 21:06 by richierich (USA)        

Model awn432sp113tw01 Speed Queen top load washer that spins but doesn't agitate. Any ideas? Google-fu is lacking

Post# 1052105 , Reply# 1   11/23/2019 at 22:39 by Yogitunes (New Jersey)        

yogitunes's profile picture
be more specific....

plugged in?

fills?

timer advances?

humming sounds?

lid closed?


Post# 1052121 , Reply# 2   11/24/2019 at 06:48 by turbokinetic (Northport, Alabama USA)        

Do these have shift solenoids like the older Kenmore have?


Post# 1052122 , Reply# 3   11/24/2019 at 07:51 by DADoES (TX, U.S. of A.)        

dadoes's profile picture
 
No shift solenoids.

Here's a parts/diagram manual.


Post# 1052123 , Reply# 4   11/24/2019 at 08:22 by turbokinetic (Northport, Alabama USA)        

Neat. So it would appear the motor would reverse directions to change between modes?


Post# 1052145 , Reply# 5   11/24/2019 at 11:58 by Yogitunes (New Jersey)        

yogitunes's profile picture
that is correct....

its a matter of two things.....timer or motor


Post# 1052263 , Reply# 6   11/25/2019 at 10:17 by richierich (USA)        

plugged in? I'm not sure what this means. Is the washer plugged in? Yes

fills? Yes. Fills normally

timer advances? Yes. Timer advances and goes through the cycle like normal

humming sounds? Everything sounds normal except when it enters spin cycle, there is some rattling like plastic pieces are rattling inside. I took off the front panel but could not see any broken pieces or loose debris

lid closed? Runs normal when lid is closed. Everything stops when lid is open


Post# 1052266 , Reply# 7   11/25/2019 at 10:32 by Repairguy (Danbury, Texas)        

Check for a stripped or broken drive bell underneath the agitator by pulling agitator straight up. Reference the parts diagram above.

Post# 1052843 , Reply# 8   12/1/2019 at 11:28 by richierich (USA)        

How do you remove the drive bell? I took out the center screw underneath the bell plug, but it won't budge. Can't tell from the parts diagram if there is another screw to remove.

Post# 1052863 , Reply# 9   12/1/2019 at 15:26 by Yogitunes (New Jersey)        

yogitunes's profile picture
add some water....see if drive bell oscillates....

or in fact, since you have the front off............does the motor turn, belt moving, pulley in motion during agitation sequence?....


now take the belt off, set to spin, is rattling noise still there?.....have you looked inside the pump?



Post# 1052873 , Reply# 10   12/1/2019 at 17:19 by richierich (USA)        

Found this youtube video for anybody else that needs to do this

CLICK HERE TO GO TO richierich's LINK


Post# 1053945 , Reply# 11   12/11/2019 at 10:30 by richierich (USA)        

Ended up being the idler pulley. Replaced the belt while we were in there as well. Hope this helps someone with the same symptoms!

Post# 1053981 , Reply# 12   12/11/2019 at 16:44 by richierich (USA)        

959P3 Idler Lever Kit includes the pulley and belt and many other pieces




Forum Index:       Other Forums:                      



Comes to the Rescue!

The Discuss-o-Mat has stopped, buzzer is sounding!!!
If you would like to reply to this thread please log-in...

Discuss-O-MAT Log-In



New Members
Click Here To Sign Up.



                     


automaticwasher.org home
Discuss-o-Mat Forums
Vintage Brochures, Service and Owners Manuals
Fun Vintage Washer Ephemera
See It Wash!
Video Downloads
Audio Downloads
Picture of the Day
Patent of the Day
Photos of our Collections
The Old Aberdeen Farm
Vintage Service Manuals
Vintage washer/dryer/dishwasher to sell?
Technical/service questions?
Looking for Parts?
Website related questions?
Digital Millennium Copyright Act Policy
Our Privacy Policy