|
Thread Number: 83005
/ Tag: Recipes, Cooking Accessories
Bubble Bandit: Dishwasher, Laundry Detergent, All-Fabric Bleach |
[Down to Last] |  |
Post# 1072810 5/16/2020 at 11:27 (1,441 days old) by Frigilux  (The Minnesota Prairie) |
||
The Bubble Bandit products arrived yesterday and gave all three a try this morning.
Dishwasher Detergent: Very disappointed! Pieces shown are all All-Clad. 4-qt. saucepan and lid used to make long-grain rice. The large, deep sauté pan browned hamburger and onions for a hotdish. Instructions say to put 2-tablespoons (2-tablespoon plastic scoop included) in the main wash cup. Add 1 tablespoon (1/2 scoop) in first wash compartment for heavily soiled loads. I put 3/4 of the scoop in the main wash cup and and the rest in the 1st wash cup. Used the 1-hour cycle as I always do. Have softened water. Other things in the load—dishes, glasses, silverware, stainless steel cake pan used to bake hotdish came out fine, but the All-Clad pieces did not. The saucepan has red rust marks inside and the starch lines on the outside of the pan from pouring the contents into a storage container weren’t budged a bit. I’ve never had these poor results using Member’s Mark pacs or Cascade Platinum pacs. Bob, I know you pack your dishwasher full, don’t pre-rinse and never pre-scrub pans. Do you have problems with the cleaning ability of Bubble Bandit on pots/pans? Did a huge load of white towels with 2 tablespoons laundry powder and 2 tablespoons all-fabric bleach. Didn’t notice any problems with cleaning. Will give Bubble Bandit dishwasher detergent a few more tries. If performance doesn’t improve, it’ s back to pods/pacs for me. Photo is upside down!
View Full Size
| ||
|
|
Post# 1072812 , Reply# 1 5/16/2020 at 12:00 (1,441 days old) by marky_mark (From Liverpool. Now living in Palm Springs and Dublin) |
||
 I haven't tried Bubble Bandit, but I have been using an equivalent product in Europe, Finish Professional powder, which is the same as Cascade Fryer Boil Out. It contains 30% phosphate (which is about 9% phosphorus) and chlorine bleach. The biggest problem I have found with this "traditional" style powder is that it struggles to shift starchy residues from rice or pasta. Its performance on protein-based soils is mixed. Really, you need enzymes to remove these things. It will work well on other soils and tea/coffee stains.
The main benefit is only seen by those who have hard water. The phosphate content is great at preventing calcium build up in the machine and on the items being washed and glasses should emerge shiner and clearer for those who have hard water. The phosphate also helps with cleaning and helps to avoid redeposit. But if you have soft water (as you and I do, thanks to a water softener) then I think you will get better results from a good detergent like Cascade Platinum etc. | ||
|
Post# 1072822 , Reply# 2 5/16/2020 at 13:25 (1,441 days old) by jamiel (Detroit, Michigan and Palm Springs, CA) |
||
 | ||
|
Post# 1072829 , Reply# 3 5/16/2020 at 14:34 (1,441 days old) by CircleW (NE Cincinnati OH area) |
||
|
My mom always used a Tuffy or Dobie scouring pad on pans used for spaghetti or macaroni before putting them in dishwasher. | ||
|
Post# 1072841 , Reply# 4 5/16/2020 at 16:54 (1,441 days old) by appnut (TX) |
||
 Eugene, I've had very few results that disappointed me. But then again, I RARELY use my 1-hour cycle. My need for BB was due to coffee & tea stains not being removed in my coffee mugs. For the past 5+ years and that's with using Cascade Platinum, Cascade Complete in pre-wash, Pots & Pans and either High-Temp wash or Sani-Rinse. For the past 2+ years, I've added Finish Detergent Booster or Lemi-Shine Detergent booster and tea/coffee stains still wouldn't budge. But I had residue-free pots & pans. And also destroyed the finish/colors on some mugs. And I have very hard water apparently. Mark's assessment about enzymes vs. phosphates is quite accurate. Earlier tis week I'd baked some chicken thighs in a pyrex dish. The above cycle/option, it came out spotless and no residue. Last night I made risotto in my Instant Pot and left the remnants and such overnight. Ran the dishwasher as stated above this morning. All the food soils came out, but some residue remains. It's unfortunate, but with my hard water I can have results for one or the other, but not combined. Maybe KitchenAid will re-introduce models with built-in water softener. Until then , I can't have it both ways. | ||
|
Post# 1072847 , Reply# 5 5/16/2020 at 17:41 (1,441 days old) by Frigilux (The Minnesota Prairie) |
||
|
Thanks for the information, guys!
Bob- Thanks for responding. I should have taken a photo of each pan separately, as the one above doesn’t show the extent of the problem well. The underside of the saucepan’s cover shows it best. Since I already have softened water and will continue to use the 1-hr. cycle—which has always provided good results—I’m going back to Member’s Mark pacs. I have about 350 of them, so I’m good-to-go, lol. Several here have commented over the years that one of the reasons vintage dishwashers cleaned effectively with 30-60 minute cycles was because the detergents back then contained phosphates; that today’s enzyme cocktail-based detergents required longer wash periods to do their work. I decided to give BB—which claims to have natural phosphates—a try since I use what is by today’s standards a short cycle similar to those on vintage dishwashers. Have a friend with a dishwasher but no water softener, so I’m going to give her the bag of BB. It will probably improve results for her and gradually get rid of hard water deposits in her machine. Bubble Bandit Laundry Detergent & All-Fabric Bleach Booster: Did a maximum capacity load of bath linens mixed with some kitchen whites and a couple of around-the-house shorts and shirts. There were only a few stains on the kitchen whites and some blood on a couple of hand towels from shaving mishaps. Used 2 scoops of detergent (which is 4, not 2 tablespoons, as stated in original post) along with 1 scoop (2 tablespoons) of booster. Everything emerged clean. Looking forward to giving the detergent/booster combo a tougher test with more heavily-stained kitchen whites some time next week. | ||
|
Post# 1072858 , Reply# 6 5/16/2020 at 18:31 (1,441 days old) by Tomturbomatic (Beltsville, MD) |
||
|
It's sad when a hoped for item disappoints; at least it was not a people. Thank you for the report. | ||
|
Post# 1073853 , Reply# 7 5/22/2020 at 23:16 (1,434 days old) by appnut (TX) |
||
|
Time for an update Eugene, I know you won't do this with your dishwasher, but I put a couple of pans of mine in the dishwasher that looked pretty bad with starchy splotches and water marks appearance that had rice and pasta cooked in it, and my Instant Pot insert. I used Pots & Pans with high-temp wash and everything was spotless. | ||
| Post# 1073855 , Reply# 8 5/22/2020 at 23:42 (1,434 days old) by qsd-dan (West) | ||
In modern dishwashers, Bubble Bandit and Cascade Fryer Boil Out are generally best used in the pre wash cycle followed by using a modern detergent in the main wash.
Make sure there's a rinse cycle between pre-wash and main wash cycles to prevent the destruction of enzymes when using both bleach and enzyme based detergents or use the enzyme detergent in the pre wash cycle first with a cold to luke-warm fill. | ||
|
Post# 1073888 , Reply# 9 5/23/2020 at 05:26 (1,434 days old) by Frigilux (The Minnesota Prairie) |
||
|
Bob- Thanks for the update. Your results with Bubble Bandit in hard water make it fairly obvious that the 1-hr cycle is not long enough to allow the detergent to do its best work. My bag of BB has been passed on to a friend, but don’t know if she’s used it yet.
Dan- Too late for me to try the BB + pac hybrid, but sounds like an interesting idea. Have to say I'm more impressed with the BB laundry detergent + all-fabric bleach/booster combo, especially in hot water. Will have to try the detergent alone at some point to see how it does. BB + booster cleans about as well as Tide Ultra Stain Release does on its own from what I've seen so far. It's cheaper to use Tide USR compared to BB + booster, but have to admit it's fun using powders for some loads. Next experiment: Tide Ultra Stain Release or Heavy Duty 10X in conjunction with Bubble Bandit All-Fabric Bleach Booster. Will either of those combinations rival the use of detergent plus liquid chlorine bleach (heretofore the gold standard for stain removal)? Tide Heavy Duty 10X: Didn't get a Culligan tank change this week so water is beginning to get hard. Trying to save the 40 gallons of soft water still in the water heater for showers and dishwasher, so washed a BobLoad of bath linens, a few kitchen whites (several piece heavily stained) and a couple of short sleeve shirts/shorts in cold water and the Normal cycle with its spray rinses. Given those far-from-ideal parameters, have to say the Tide (filled to line 4 in cap; for large loads) didn't do too badly. Pasta sauce stains were not removed, but they were lightened quite a bit. Culligan is scheduled to be here Tuesday morning, thank God. This post was last edited 05/23/2020 at 09:49 | ||
|
Post# 1073966 , Reply# 11 5/23/2020 at 17:25 (1,434 days old) by Frigilux (The Minnesota Prairie) |
||
|
I thought about using Bubble Bandit + booster this morning, but having chosen to wash a huge, primarily white load in cold water using spray rinses, decided to go with Tide 10X as my best bet. CR noted in their tests that Tide USR and 10X did well in their separate hard water test, as compared to Persil Proclean + Stain Fighter, whose cleaning power was diminished in hard water.
Monday, I wash another BobLoad of bed linens, kitchen whites, and some around-the-house clothes (short sleeve buttoned shirts and shorts). Will probably use cold water and the Normal cycle again. May try BB + Booster or, as you suggested, some of each. I can feel the water getting harder in the cold line, so am doing everything I can to carefully parse out the still-soft water in the water heater. And, of course, every gallon of hot water used is replaced by a gallon of hard water. In fact, just as an experiment, am going to run a maximum capacity dishwasher load in warm water in a couple of hours, just to see if items emerge clean using a Member's Mark pac. Since the Whirlpool is portable, water temp can be adjusted at the tap. I have three nonstick frying pans of various sizes, but normally get great results with starch lines from pasta & rice in my All-Clad pans using the Member's Mark pacs. | ||
|
Post# 1074008 , Reply# 12 5/23/2020 at 20:43 (1,433 days old) by Frigilux (The Minnesota Prairie) |
||
|
Update: Just washed an at-capacity load in the dishwasher with warm water. Placed the faucet exactly at the midpoint between hot and cold water, added a Member’s Mark Ultimate Clean pac, chose the 1-hr cycle and hoped for the best. Did not run water to purge hot water pipe. Water draining after final rinse was about 90 degrees.
Opened the door to no steam whatsoever and decided to hand dry the load—primarily because I couldn’t wait to see how things turned out. Much to my surprise...everything was clean. Even the three plastic Ziploc containers that had various portioned casseroles in them were grease-free. Cooked off 8 burgers—four in an All-Clad high-sided sauté pan and four in a nonstick frying pan. I’d run a wet paper towel over the interior of the All-Clad prior to putting it in the machine, but it was by no means clean. It emerged gleaming. This is certainly not something I plan to do regularly, but just may continue to do it between now and Tuesday, when the Culligan tank finally gets exchanged. Trying to parse out the still-soft water in the water heater for showers. At any rate, I guess these newly reformulated pacs from Sam’s Club do deserve their top-rated status at CR. | ||
|
Post# 1074024 , Reply# 13 5/23/2020 at 22:31 (1,433 days old) by Tomturbomatic (Beltsville, MD) |
||
|
The two non-stick pans I bought for starchy things are All-Clad. I always wash them by hand since there have been reports in the past about the non-stick coating failing if put in the dishwasher. Nothing sticks so there is no cleanup problem with them. | ||
|
Post# 1074057 , Reply# 14 5/24/2020 at 05:50 (1,433 days old) by ozzie908 (Lincoln UK) |
||
#appnut
OK I have to ask how come most of your dishwashers do not have a water softener built in?
I cannot think of a single model in the UK that doesn't have one, The only one I can recall is a Candy back in the 80's but since then they all have them. You can turn them off if you have naturally soft water to a whole house softener but they are rare I have a Miele dishwasher that you can adjust the setting on its set about midway and everything is clean in fact the only thing it often fails on is a Crueset casserole dish I tend to use the sensor setting and it gets a finish tab in the main wash occasionally I throw in a sanitiser tablet in the prewash if the plastic boxes etc are tinged with tomato. Admittedly it takes a while to wash as it only has a cold water connection but as we use it every night and sometimes during the day as well am never in a rush for it to do its work... Austin This post was last edited 05/24/2020 at 07:56 | ||
| Post# 1074060 , Reply# 15 5/24/2020 at 06:49 (1,433 days old) by mark_wpduet (Lexington KY) | ||
Rinse cycle AFTER prewash?
OK, so to chime in here.
To get a little chlorine I add a splash of bleach before starting the dishwasher. There's that first fill, then drain...then fill for wash, then I think 2 rinses after the main wash. I've never had an issue of bleach degrading finish powerball performance. I think because of the fact that I'm already only using a little bleach to begin with, which gets diluted with the fill.....so once that's drained, there's hardly any left. But a little bleach goes a LONG way. I can tell a major difference if I don't use the bleach. Oh, I don't do the quick wash. Why? I tried it once on my Maytag and it's NOT even an hour! Results were horrible. I think it only ran 30 minutes. But for whatever reason, my Maytag doesn't run for what I feel like is a really long time anyway. Maybe 90 min's? (ish) on normal high temp tough scrub. The only cycle that gets way out of hand with the time is the Jetclean steam cycle, which I think is over 3 hours and maybe close to 4 and uses a TON of water. | ||
|
Post# 1074063 , Reply# 16 5/24/2020 at 07:17 (1,433 days old) by DADoES (TX, U.S. of A.) |
||
 Austin, dishwashers with water softeners are not common on the US market. European-sourced brands (Miele, Bosch, maybe Asko) may have them on some higher-end models. F&P has DDs both with and without. KA had an equipped model, don't know if it's still available. The typical consumer doesn't consider that a dishwasher can have a built-in softener, and those that don't have a whole-house softener have no clue how they work. A typical comment on a discussion board about "adding salt to my dishwasher" from someone who has a unit with a softener invariably brings questions from people thinking that simply adding table salt along with the detergent will result in softened water in their non-softener machines. | ||
|
Post# 1074068 , Reply# 17 5/24/2020 at 07:56 (1,433 days old) by ozzie908 (Lincoln UK) |
||
|
Oh I see :) | ||
|
Post# 1074076 , Reply# 18 5/24/2020 at 09:22 (1,433 days old) by eronie (Flushing Michigan) |
||
|
You cannot regenerate any softener with HOT water! US machines are hot fill! European machines are cold fill! | ||
|
Post# 1074079 , Reply# 19 5/24/2020 at 10:11 (1,433 days old) by DADoES (TX, U.S. of A.) |
||
|
| ||
|
Post# 1074084 , Reply# 20 5/24/2020 at 11:54 (1,433 days old) by eronie (Flushing Michigan) |
||
|
I've never seen a softner equipped dishwasher in the us. Hooked up to cold fill on 120 volts a 3 hour cycle would take all day. Euro electric must be way cheeper than hours but it is 220 volt. Almost all of their appliances washer dishwasher are cold fill. | ||
|
Post# 1074092 , Reply# 21 5/24/2020 at 12:42 (1,433 days old) by marky_mark (From Liverpool. Now living in Palm Springs and Dublin) |
||
|
Dishwashers in Europe can normally be connected to either cold or hot water, with a maximum incoming temperature of 60 or 70 °C often specified (140 or 160 °F). The water softener can be regenerated with hot or cold water. Most are connected to cold water. Some specify they should be connected to cold water only.
Most in the USA say that they should be connected to hot water, including the Kitchenaid models with built-in water softeners, usually with a recommended incoming temp of 50 °C (120 °F). Some older ones recommended higher temps such as 60 °C (140 °F) or more. Some can still work fine on cold water, depending on the cycle and options chosen. Others will not work as well and some will not heat the water at all on certain cycles. | ||
|
Post# 1074097 , Reply# 22 5/24/2020 at 13:54 (1,433 days old) by DADoES (TX, U.S. of A.) |
||
|
3 hr cycle all day No so much. I checked a few mins ago with a 5-gallon bucket I have marked in gallons. Water heater at 50°C (122°F), took ~2-1/3 gals to get a warm flow at the faucet due to plumbing distance from the heater. 3 gals for nicely hot. I usually have the water heater at 103°F (for showering) so that's moderately warm even if flushing the supply (unless I raise it temporarily for the dishwasher, which usually I don't). DD takes 0.8 gals per fill, so that's ~4 fills of continuous-running water to flush the supply line if I don't do it first. More counting dwell-time between fills. It raises the temp a little faster than 1°F per minute, maybe 1.3°F. Longest cycle is estimated 132 mins, which includes ~28 mins dry time. True, that's less than 3 to 4 hours on some intense cycles nowadays, but it has never run anywhere near all day, LOL. Anywho, IMO, the 3- and 4-hr cycles nowadays aren't for water heating but to give enzyme detergents a LONG time to work, coupled with lower spray pressures from reduced water volume and smaller pumps. | ||
|
Post# 1074100 , Reply# 23 5/24/2020 at 14:15 (1,433 days old) by Logixx (Germany) |
||
Euro electric must be way cheeper than hours | ||
|
Post# 1074110 , Reply# 24 5/24/2020 at 15:35 (1,433 days old) by appnut (TX) |
||
|
| ||
|
Post# 1074197 , Reply# 26 5/25/2020 at 01:03 (1,432 days old) by abcomatic (Bradford, Illinois) |
||
|
I have used BB for years and love it. Always clean dishe and I also us BB for the laundry. Every thing comes out just fine. Gary | ||
|
Post# 1074228 , Reply# 27 5/25/2020 at 09:45 (1,432 days old) by ozzie908 (Lincoln UK) |
||
|
According the instructions for my Miele dishwasher
You can connect it to the hot water if its available and cheaply heated IE by solar panels or some other method of creating cheap hot water, It cannot be above 60c and it has a regeneration unit !
No point using hot water here as the boiler is too far from the sink unless you purged the line it would be a waste of time and energy, Most houses these days do not have a hot water tank as they take up room are costly to heat especially electrically so its more convenient to just use the cold supply same for the washer. However I do have a US model whirlpool washing machine that is connected to the hot water as its in the same room as the boiler and so it gets the hot water before its finished filling it takes a good 30 minutes off the cycle as it gets to temp quicker I used to have it on cold only but may as well utilise the boiler it doesn't do anything in the warmer weather :) Austin | ||
|
Post# 1074815 , Reply# 29 5/29/2020 at 04:59 (1,428 days old) by askolover (South of Nash Vegas, TN) |
||
 I don't know how it works but Miele USA has a water softener dishwasher with hot fill
CLICK HERE TO GO TO askolover's LINK | ||
|
Post# 1074826 , Reply# 30 5/29/2020 at 06:36 (1,428 days old) by appnut (TX) |
||
|
| ||
|
Post# 1074954 , Reply# 31 5/30/2020 at 08:14 (1,427 days old) by Frigilux (The Minnesota Prairie) |
||
|
Bubble Bandit Laundry Detergent and All-Fabric Bleach Booster Update:
Have used BB detergent with and without the addition of a scoop of all-fabric bleach on about 10 loads. Here's what I've found, using a 2017 Speed Queen top-loader, very soft water, hot water temp at the tap around 140-145 degrees. 1. BB detergent cleans loads without a lot of stains well. Adding the all-fabric bleach definitely improves stain removal performance. 2. BB + all-fabric bleach booster cleans about as well as Tide Heavy Duty 10X and Persil Proclean + Stain Fighter do on their own. 3. The best stain removal results on heavily-soiled kitchen whites are still achieved with a top-shelf detergent and liquid chlorine bleach (I use original Clorox). All stains always completely removed. Will I order Bubble Bandit products online again? Probably not--but not because they're ineffective products. It's just that the addition of phosphates doesn't seem to make much difference in very soft water, and I can find products that work just as well or better on the shelf at my grocery store. Those with hard water may find some benefit, but I honestly didn't notice a big drop in performance from Persil + Stain Fighter or Tide HD 10X when my water was hard for the better part of a week. I was even impressed with the aforementioned versions of Tide and Persil when I washed in hard, cold water for a few days (to conserve the soft water that was still in the water heater tank). Of course, neither performed as well as when using hot water, but they did better than I expected them to. Did not try BB products in cold water. Also, take into account that the Speed Queen's maximum wash time is about 15-16 minutes. Results may be noticeably better in the highly-concentrated environs of an HE front-loader coupled with wash periods that can be up to three times longer. This post was last edited 05/30/2020 at 08:45 | ||
|
Post# 1075101 , Reply# 32 5/31/2020 at 10:01 (1,426 days old) by bajaespuma (Connecticut) |
||
Soft Water is the key I have lived and laundered in many different places with different water hardnesses; after 50 years of dishwashing and laundering I've concluded that the most important benefit to all of this is naturally soft water--no product beats it. I've been using some of the BB products and I can't honestly report that I see any improvement for the expense, maybe a little better rinsing in the laundry. If I still lived in Dutchess County NY, I might have more to talk about. The hardest water I've ever experienced was in Strasbourg France; there were many phosphate booster products that one HAD to use in the clothes washer and the dishwasher just to keep the machines from caking up with calculus.
View Full Size
| ||
| Forum Index: |
| Other Forums: |
|
|
|
|
|
Comes to the Rescue!
